Refer to the Address Table and assign the correct IP address to the subinterface.Set the encapsulation type to 802.1Q and assign VLAN 10 to the subinterface.Part 3: Configure Subinterfaces Step 1: Configure subinterfaces on R1 using the 802.1Q encapsulation. Why were the pings unsuccessful? Each VLAN is a separate network and requires a router or a layer 3 switch to provide communication between them. Issue the show vlan brief command to verify VLAN configuration.ġ default active Fa0/1, Fa0/2, Fa0/3, Fa0/4ġ005 trnet-default active Step 3: Test connectivity between PC1 and PC3.įrom PC1, ping PC3.S1(config-if)# switchport access vlan 30.S1(config-if)# switchport access vlan 10.Configure interface F0/6 and F0/11 as access ports and assign VLANs.S1(config)# vlan 10 S1(config-vlan)# vlan 30 Step 2: Assign VLANs to ports. Return to Realtime mode and create VLAN 10 and VLAN 30 on S1. Part 2: Add VLANs to a Switch Step 1: Create VLANs on S1.
#Configure router on a stick packet tracer mac
Without a MAC address, PC1 cannot create an ICMP echo request. PC1 and PC3 are not on the same network, so S1 doesn’t forward PC1’s ARP request (a broadcast packet) to VLAN30. What process failed and why? The ARP process failed because the ARP request never reached PC3. Click Capture/Forward to see the steps the ping takes between PC1 and PC3.Switch to Simulation mode by clicking the Simulation tab or pressing Shift+S.Step 2: Switch to Simulation mode to monitor pings. Because the two PCs are on separate networks and R1 is not configured, the ping fails. When the link lights are green for PC1 and PC3, ping between PC1 and PC3. Wait for switch convergence or click Fast Forward Time a few times. Part 1: Test Connectivity Without Inter-VLAN Routing Step 1: Ping between PC1 and PC3. Finally, you will enable trunking and verify connectivity between VLANs. You will then configure VLANs and inter-VLAN routing. In this activity, you will check for connectivity prior to implementing inter-VLAN routing. Part 4: Test Connectivity with Inter-VLAN Routing Scenario Part 1: Test Connectivity without Inter-VLAN Routing TopologyĦ.3.3.6 Packet Tracer – Configuring Router-on-a-Stick Inter-VLAN Routing Addressing Table Device Packet Tracer – Configuring Router-on-a-Stick Inter-VLAN Routing (Answer Version)Īnswer Note: Red font color or Gray highlights indicate text that appears in the Answer copy only. Version 5.02Ħ.1.1.5 Packet Tracer – Who Hears the BroadcastĦ.1.2.7 Packet Tracer – Investigating a VLAN ImplementationĦ.2.1.7 Packet Tracer – Configuring VLANsĦ.2.2.4 Packet Tracer – Configuring TrunksĦ.2.3.7 Packet Tracer – Troubleshooting a VLAN Implementation – Scenario 1Ħ.2.3.8 Packet Tracer – Troubleshooting a VLAN Implementation – Scenario 2Ħ.3.3.6 Packet Tracer – Configuring Router-on-a-Stick Inter-VLAN RoutingĦ.3.3.8 Packet Tracer – Inter-VLAN Routing ChallengeĦ.4.1.2 Packet Tracer – Skills Integration Challenge After you review all questions, You should practice with our online test system by go to "Online Test" link below. Each version have 1 to 10 different questions or more. While you take online test with, You may get random questions from all version. We recommend you to go thought all version if you are not clear. What is your version? It depends on your instructor creating your class. The latest version is version 6.0 in 2018. From year to year, Cisco has updated many versions with difference questions.
0 kommentar(er)
